Tecumseh engine model, specification, and serial numbers or (date of manufacture, DOM) are stamped into the blower housing or located on a decal on the engine in locations as illustrated (diag. NOTE: On some LEV engines, a cover bezel must be removed to provide access to the identification decal (diag 1xddfdf. The engine identification decal also provides the applicable warranty code and oil recommendations (diag. Emissionized engines that meet the California Air Resource Board (C.A.R.B.) or the Environmental Protection Agency (E.P.A.) standards will include additional required engine information on the engine decal (diag. The first letter designation in a model number indicates basic type of engine. The number designations following the letters indicate the horsepower or cubic inch displacement.
The number following the model number is the specification number. The last three numbers of the specification number indicate a variation to the basic engine specification. The serial number or D.O.M. Indicates the production date. Using model LEV115-57010B, serial 8105C as an example, interpretation is as follows:.
Tecumseh Compressor Model Number L…![]()
LEV115-57010B is the model and specification number. LEV Low Emissions Vertical.
115 Indicates a 11.5 cubic inch displacement. 57010B is the specification number used for properly identifying the parts of the engine. 8105C is the serial number or D.O.M.
(Date of Manufacture). 8 first digit is the year of manufacture. 105 indicates calendar day of that year (105th day or April 15, 1998). C represents the line and shift on which the engine was built at the factory. Engine Family: Engine Tracking Information Short Blocks. New short blocks are identified by a tag marked S.B.H. (Short Block Horizontal) or S.B.V (Short Block Vertical).
Original model identification numbers of an engine should always be transferred to a new short block for correct parts identification (diag. This symbol points out important safety instructions which if not followed could endanger the personal safety of yourself and others.
Follow all instructions. Fuel Tecumseh strongly recommends the use of fresh clean unleaded regular gasoline in all engines. Unleaded gasoline burns cleaner, extends engine life and promotes better starting by reducing combustion chamber deposits. Reformulated and Oxygenated Fuels Reformulated fuels containing no more than 10% Ethanol, 15% MTBE, 15% ETBE or premium gasoline can bu used if unleaded regular gasoline is not available.
Leaded fuel may be used in countries where unleaded fuel is not available. Never Use Fuel Containing Methanol. Engine Oil Use a clean, high quality detergent oil. Be sure original container is mark: A.P.I. Service SF thru SJ. The use of multigrade oil may increase oil consumption under high temperature, high load applications. NOTE: Do not use SAE10W40 Oil.
For summer (above 32°F, 0°C): Use SAE 30 oil part #730225 (1 quart,.946 liter container) in high temperature, high load applications. 10W30 is an acceptable substitute. For winter (below 32°F, 0°C): Use Tecumseh synthetic oil part #730263 (1 quart,.946 liter container) approved for use in all winter temperature ranges, or S.A.E. 5W30 oil part #730226 (1 quart,.946 liter container).
10W is an acceptable substitute. 0W30 should only be used when ambient temperature is below 0°F, -18°C.
![]()
Capacities Engine Model Oz. LAV30-50, TVS75-120, LEV80-120 21 630 ECV100-120, TNT100-120 21 630 V & VH50, 60, 70 27 810 TVM 125, 140 27 810 TVM & TVMXL 170, 195, 220 32 960 VM70, 80, 100 32 960 VH1 H & HSK30, 35, HS & HSSK40, 50 21 630 H, HH & HSK50, 60, 70 19 570 HM & HMSK70, 80, 100, HMXL70 24 720 VSK90-100 21 630 HHM Europa Models Oz. Vantage 21 630 Prisma 21 630 Synergy 21 630 Synergy '55' 27 810 Spectra 21 630 Futura 21 630 Centura 21 630 HTL 21 630 BVS 21 630 BH Series 21 630 Geo Tech Series 30-50 21 630 Oil Change Intervals. Change the oil after the first two (2) hours of operation and every 25 hours thereafter, or more often if operated under dusty or dirty conditions, extreme temperature, or high load conditions.
Tecumseh Compressor Serial Number Decoder
Check the oil each time the equipment is user or every 5 hours. Position the equipment so the engine is level when checking the oil. CAUTION: Remove the spark plug wire before doing any service work on the engine. Oili Change Procedutre: Locate the oil drain plug. On some unites this plug is located below the deck through the bottom of the mounting flange. Other units drain at the base of the engine above the deck or frame.
If access to the drain plug is restricted by the equipment it may be necessary to drain the oil by tipping the mower in a position that would allow the oil to drain out of the fill tube. On units that the drain plug is accessible, remove the plug and allow the oil to drain into a proper receptacle. Always make sure that drain oil is disposed of properly. Once the oil is drained, reinstall the plug and fill the engine with new oil to the proper capacity. Tune-Up Procedure The following is a minor tune-up procedure.
When this procedure is completed, the engine should operate properly. Further repairs may be necessary if the engine's peformance remains poor. CAUTION: Remove the spark plug wire before doing any service work on the engine. Service or replace the air cleaner as needed. Inspect the level and conditions of the oil and change or add oil as required.
Remove the blower housing and clean all dirt, grass or debris from the intake screen, cylinder head, cylinder cooling fins, carburetor, governor levers and linkage. When replacing the spark plug, consult the parts breakdown for the proper spark plug to be used in the engine being serviced. Set the spark plug gap to.030' (.762 mm) and install the spark plug in the engine. Tighten the spark plug to 15 foot pounds of torque (20.4 Nm). If a torque wrench isn't available, screw the spark plug in as far as possible with hand, and use a spark plug wrench to turn the spark plug 1/8 to 1/4 turn further if using the old spark plug, or 1/2 turn further if using a new spark plug. Make sure all ignition wires are free of abrasions or breaks and are properly routed so they will not rub on the flywheel.
Properly reinstall the blower housing, gas tank, fuel line and air cleaner assembly if removed. Make sure all remote cables are properly adjusted for proper operation. See chapter 4 under 'Speed Controls and Linkage'.
Reinstall the spark plug wire, add fuel and oil as necessary, and start the engine. Storage Drain all fuel from the machine to,keep fuel from degrading and causing damage to fuel related parts of the machine. (If the engine is to be unused for 30 days or more).
Scroll Technologies Compressors Stroll Technologies was a joint venture between Carlyle Compressors (a division of Carrier) and Bristol Compressors, and the compressors were sold exclusively through these partners as the 'Millenium' for Carlye and the 'Infinity for Bristol. In September 2006, Danfoss, a Danish company purchased Stroll Technologies from Carlyle and Bristol. The breakdown of the serial number is Digit 1: S for Scroll Technologies Digits 2-3: Week Manufactured Digits 4-5: Year Manufactured Digits 6: State (K for Arkansas) Digits 7-11: Sequence # During Week.
• Posts must be related to the Netherlands. Disney films in order of release.
Scroll Technologies Compressors Stroll Technologies was a joint venture between Carlyle Compressors (a division of Carrier) and Bristol Compressors, and the compressors were sold exclusively through these partners as the 'Millenium' for Carlye and the 'Infinity for Bristol. In September 2006, Danfoss, a Danish company purchased Stroll Technologies from Carlyle and Bristol. The breakdown of the serial number is Digit 1: S for Scroll Technologies Digits 2-3: Week Manufactured Digits 4-5: Year Manufactured Digits 6: State (K for Arkansas) Digits 7-11: Sequence # During Week.
Danfoss Scroll Compressors - HCM, HDM & HRM Series - Scroll See Danfoss Compressors Model Number Chart Reference (at the bottom of this page) For Air Conditioning & Heat Pump Application Features:. Scroll technology. High efficiency-up to 11.6 EER. Inherent motor protection. Low vibration & noise. Painted shell.
Refrigerant - HCFC-22. Wire connections − Q = Quick connect − S = Screw. Foot print - 7.5 x 7.5. No crankcase heater + Suitable for 50 Hz.
Operation. NOTE: When substituting compressors always check the capacitor MFD and voltage (when required) and replace if necessary. The capacitor MUST be the proper MFD and voltage for the compressor.
. Cookie Consent We use cookies to improve your website experience. To learn about our use of cookies and how you can manage your cookie settings, please see our. By continuing to use the website, you consent to our use of cookies. Welcome to HVAC-Talk.com, a non-DIY site and the ultimate Source for HVAC Information & Knowledge Sharing for the industry professional! Here you can join over 150,000 HVAC Professionals & enthusiasts from around the world discussing all things related to HVAC/R.
You are currently viewing as a NON-REGISTERED guest which gives you limited access to view discussions To gain full access to our forums you must; for a free account. As a registered Guest you will be able to:. Participate in over 40 different forums and search/browse from nearly 3 million posts. Post photos, respond to polls and access other special features.
Gain access to our free AOP (Ask a Professional) Section to get real answers for your questions. All this and much more is available to you absolutely free when you; for an account, so today! We suggest not registering using an AT&T, BellSouth, AOL or Yahoo email address. If you have any problems with the registration process or your account login, please. Got an old D-B unit with a junk TX. Anyone know how to read the nomenclature?
What's the tonnage? I'm tempted to say 1600 btu on the condensing unit? Never seen a model number with an ampersand in it. Condensing unit: AR-16H&C Evap. Unit: C145 None of our dealers can tell me anything about D-B.I've got D/B literature dating from the 1960's and find nothing even close to that model number. Is this a belt-drive or a semi-hermetic?
I don't recall ever seeing one with a 16 in the model number. For a short time in the 1960's they did make some 1/4 and 1/3 hp hermetic condensing units with Kelvinator or Tecumseh compressors, but I have no info left for those.
Tecumseh Compressor Serial Number Nomenclature Number
Quick Navigation. Site Areas. Forums.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |